The short version
- 01What it is: 80% polyester / 20% rayon (TR), serge twill, 360 g/m², 57/58 inch (145–147 cm) width, for suiting and uniforms.
- 02Dry rubbing 4–5 under ISO 105-X12:2016 — a strong result for a polyester-rayon blend, and the reason YA8006 holds up in office and school uniform programmes.
- 03Wet rubbing 2–3 under the same method. This is our honest weak spot and we would rather you specified it than discovered it after a bulk wash test.
- 04Laundering 4–5 for colour change with 4–5 cross-staining to acetate, cotton, polyamide, polyester, acrylic and wool (ISO 105-C06:2010).
- 05Pilling 4–5 after 7,000 Martindale cycles (ISO 12945-2:2020), plus 100+ ready-to-ship colours and a published eight-step order flow.
The product
YA8006 in eight lines of specification
YA8006 is an 80% polyester / 20% rayon blend, woven as serge twill at 360 g/m² and 57/58 inch wide, engineered for business suiting, office uniforms and school uniform programmes.
Before we get to the laboratory numbers, it is worth being clear about what you would actually be ordering. Polyester-rayon — abbreviated TR by almost every mill in Shaoxing and Keqiao — takes the drape and the soft, slightly fluid hand of viscose and adds the abrasion and crease retention of polyester. If you are new to the blend, our TR fabric guide walks through the full polyester-rayon family before you commit to one construction. That combination is why TR replaced pure polyester in mid-market suiting across Europe, Russia, Africa and the Gulf over the last decade, and it is why a TR fabric behaves very differently from a 100% polyester suiting of the same weight. TR also comes in both stretch and non-stretch versions, and where stretch is needed we build it as polyester-rayon-spandex with either four-way stretch or warp stretch; in design terms we stock solid colours alongside plaid and stripe.
YA8006 is strategically sold to a wide range of countries, including Russia, Africa and other international markets. If you want the commercial background, our note on why most customers choose YA8006 for uniforms explains the market pull behind this item. It is the reference article in our polyester rayon fabric collection and the single item behind our TR category page, so every number below comes from the same production route your order would use.
| Parameter | YA8006 specification | Test method |
|---|---|---|
| Item number | YA8006 | — |
| Composition | 80% polyester / 20% rayon (TR) | — |
| Weave | Serge twill | — |
| Weight | 360 g/m² | — |
| Width | 57/58 inch (145–147 cm) | — |
| Dry rubbing fastness | Grade 4–5 | ISO 105-X12:2016 |
| Wet rubbing fastness | Grade 2–3 | ISO 105-X12:2016 |
| Colour change after laundering | Grade 4–5 | ISO 105-C06:2010 |
| Cross-staining (7 fibres) | Grade 4–5 | ISO 105-C06:2010 |
| Pilling after 7,000 cycles | Grade 4–5 | ISO 12945-2:2020 |
| Ready colours | 100+ in stock | — |
| Minimum order | One roll per colour | — |
| End use | Suit, uniform, trousers | — |
All grades reproduced from our internal examination report. Method numbers are the exact ISO parts used; editions are current at the date of testing.
Two practical notes on that table. First, at 360 g/m² this is a mid-to-heavy weight: it is an autumn/winter suiting and trouser cloth, and it is the weight we recommend for winter school uniforms and office uniform programmes. If your climate runs hot, ask us for the 240–280 g/m² version of the same construction rather than trying to make a 360 g/m² cloth work in a hot climate. Second, the width matters commercially as much as technically: 57/58 inch (145–147 cm) is a wide suiting width, which reduces the number of body panels a marker needs and therefore reduces cutting waste.
Before the numbers
Why “Grade 4–5″ without a method number is close to meaningless
A colour fastness grade is meaningless without the ISO part, the edition year and the scale it was read against — because ISO 105 is not one test but a large family of parts, and each answers a different question.
We have seen too many buyers receive a certificate that says only “ISO 105″ and treat it as a quality seal. It is not. According to the International Organization for Standardization, ISO 105-X12:2016 is specifically the method for determining the resistance of textile colour to rubbing off and staining other materials; the ISO 105 series as a whole covers washing, light, sweat, water, sea water, dry cleaning, colourfastness to rubbing in small areas, and more besides. We keep a plain-English primer on how to test fabric colour fastness if you want the practical side of running these methods. A supplier who quotes “ISO 105″ without the part number has told you that they have a colour fastness test, not which question they answered.
Edition numbers are equally important, and this is where the catalogue is genuinely helpful. On the ISO entry for ISO 105-X12:2016, the 105-X12:2001 edition is listed as a withdrawn predecessor while the 2016 edition is the one in force, and the catalogue records that this publication was last reviewed and confirmed in 2021 and therefore remains current. For laundering, the 1994 edition of ISO 105-C06:2010 and both of its 2002 corrigenda are withdrawn, leaving the 2010 edition published and confirmed. And for pilling, ISO 12945-2:2020 is the current edition of the modified Martindale method, with the 2000 edition withdrawn and the 2020 edition itself under systematic review.
That is why our own report cites the full reference each time — ISO 105-X12:2016, ISO 105-C06:2010, ISO 12945-2:2020 — rather than a family name. If you are comparing two mills’ certificates, the first thing to check is not the grade but whether the method and the edition are the same.
One more piece of vocabulary. In the ISO 105 scale, Grade 5 means no perceptible change of colour and Grade 1 means severe change, with 2, 3 and 4 in between. So “Grade 4–5″ is not a single measured point: it is a band, and we report it as a band when that is what the laboratory returned. A supplier who writes “Grade 5″ on a spec sheet for a fabric that actually returned 4–5 has not improved the fabric; they have only improved the certificate.
Rubbing fastness
Dry rubbing 4–5, wet rubbing 2–3: the honest part
Dry rubbing came back at Grade 4–5 and wet rubbing at Grade 2–3 under the same ISO 105-X12:2016 method, and the gap between them is a fibre property rather than a manufacturing defect.
As the ISO abstract for ISO 105-X12:2016 puts it, two tests may be made on the specimen — one with a dry rubbing cloth and one with a wet rubbing cloth — and the colour transfer is read against a backing cloth on a five-point scale. Our dry result of 4–5 puts YA8006 in good shape for the abrasion a garment actually sees in normal life — a chair back, a desk edge, a lapel rubbing against a shirt front, a school bag against a trouser seam, a seatbelt across a shoulder.
The wet result of 2–3 is lower, and there is a reason that shows up in almost every polyester-rayon blend we test. Regenerated cellulose fibres — viscose and rayon — lose a substantial part of their dry strength when saturated with water, so the same rubbing action that a dry fabric shrugs off can pull colour off a wet one. It is a property of the fibre family, not a fault in the weave or the dye house. This is why we will not describe a wet rubbing grade as “commendable” simply because it is two points below the dry grade.
What it means commercially depends on how the garment is worn and washed:
- Office suits, hospitality and airline uniforms, school uniforms — dry contact dominates. A Grade 4–5 dry result is the number that matters, and YA8006 is well matched to these programmes.
- Wet or damp contact, heavy perspiration, exposed outerwear, garments laundered while still warm — wet rubbing becomes the governing number. Here YA8006 is adequate rather than outstanding.
- Darker shades — deep navy and black have more visible dye surface, so we advise buyers who specify dark TR to confirm the wet rubbing requirement against their own wash and wear protocol rather than assume the dry grade transfers.
Our recommendation, which we put in writing for every quote, is that buyers who care about wet rubbing should specify the number they need — for example a minimum Grade 3 wet — and let us confirm in the lab whether a particular colour and construction meets it before the bulk is dyed. Asking for that confirmation is cheaper than a returned bulk of dyed fabric. We also test each new colour against its own shade, because a grade on a mid-tone tells you very little about the same construction in black.
Washing
Colour change 4–5 and seven-fibre cross-staining at 4–5
After domestic and commercial laundering under ISO 105-C06:2010, YA8006 held Grade 4–5 for colour change and Grade 4–5 for staining onto every one of seven adjacent fibres.
ISO 105-C06 is the method for colour fastness to domestic and commercial laundering: repeated wash cycles with a reference detergent, then an assessment of how much colour has moved off the specimen and how much has landed on the companion fabrics. The standard’s own abstract is worth reading, because it tells you what a result is worth: one multiple (M) test may in some cases be approximated by up to five domestic or commercial launderings at temperatures not exceeding 70 °C, while the M tests are more severe than the single (S) tests because of increased mechanical action. In other words, the number on our report is not one wash. It is closer to five.
Two results matter here. The first is our own colour change grade of 4–5 — the fabric simply does not shift colour through a wash cycle. The second is the cross-staining result, and this is the one most buyers never ask about. We ran the specimen against seven fibres at once: acetate, cotton, polyamide, polyester, acrylic and wool. All seven came back at Grade 4–5, meaning essentially no dye transferred off our navy or charcoal onto any of them.
That result is worth more than it sounds. A mixed laundry load is the normal condition for a uniform programme — a navy suit, a white shirt, a charcoal jacket and a polyester-lined raincoat all in the same machine on the same cycle. A fabric that bleeds onto cotton in that machine is a quality-control problem for whoever washes it; a fabric with a 4–5 staining grade against all seven fibres removes that risk entirely, which is why we consider it more useful to a uniform buyer than the headline colour change number.
YA8006 ready goods, solid colour range
There is one scope limit you should know about, and it is in the standard itself rather than in our lab. The abstract of ISO 105-C06:2010 states that the method covers domestic and commercial laundering for normal household articles, and warns that industrial and hospital articles may be subjected to special laundering procedures which may be more severe in some aspects. That distinction matters if you supply scrubs into a hospital laundry contract or workwear into an industrial laundry, because those programmes run hotter, longer and with more aggressive chemistry than a domestic cycle. If that is your end use, say so at quotation stage and we will run the additional industrial procedures on your specific colour.
Pilling
Grade 4–5 after 7,000 Martindale cycles
Under the modified Martindale method of ISO 12945-2:2020, YA8006 still graded 4–5 for surface pilling after 7,000 abrasion cycles.
Surface pilling is the small knobbly ball that forms on a fabric face when loose fibre ends work to the surface under friction. On a suiting fabric it is a quality perception problem before it is a durability problem: a suit that pills at the seat or the elbow signals poor quality faster than any other visible fault. We covered the test itself in a separate piece on how to evaluate anti-pilling performance.
ISO 12945-2:2020 is the current edition of the modified Martindale method, the reference procedure for determining a fabric’s propensity to surface pilling, fuzzing and matting. We run the specimen through 7,000 cycles and then assess the abraded face. A 4–5 result at that cycle count is a genuinely good outcome for a polyester-rayon suiting, and it is a direct consequence of the construction: the serge twill has a tight, dense surface, and the polyester component resists the fibre-fatigue that creates pills.
Two honest qualifications. Pilling is a surface property, not a wear-life measurement — it tells you the face of the cloth will not fuzz up, not how many years of daily wear the garment will survive. And a pilling grade does not predict seam strength. If your spec sheet needs wear life rather than surface appearance, that is a different number, measured under ASTM D4966, the standard test method for abrasion resistance of textile fabrics using the Martindale abrasion tester. We can run that on request alongside the pilling assessment, and we would rather you had both than either alone.
Checked and striped designs run alongside the solids
The gap
What the report does not tell you
Three strong grades do not make a complete specification, because the most common complaint in this industry is a report that answers the questions nobody thought to ask.
We publish our three results because they are the three that decide whether a TR fabric can hold its colour and its surface through a working life. But if you are writing a fabric specification for a brand, here is what is not covered, so you can request it rather than discover it at audit stage:
- Light fastness. Nothing in ISO 105-X12, 105-C06 or 12945-2 measures how a colour responds to daylight and artificial light. That is a separate ISO 105 method, and for a fabric sold as a curtain-adjacent or window-side suiting it can be the number that matters most. We can add it.
- Dimensional stability. A fabric can hold its colour perfectly and still grow a centimetre in the seam. Shrinkage and dimensional change after washing are measured separately, and for a uniform programme with a fixed garment size they decide whether you re-cut a whole production run.
- Shade variation between dye lots. This is a commercial reality rather than a laboratory property, and it is the reason we recommend that you approve a lab dip or a production sample against the physical roll before we dye in bulk. Two rolls from the same batch can read a shade apart under a neutral light, and no certificate removes that.
- Seam slippage and tensile or tear strength. Not covered by any of the three colour and surface methods, and relevant if you are cutting a heavy 360 g/m² suiting on a particular seam construction.
- Fibre composition on the label — and which word you are allowed to use. If you sell into the European Union, the fibre composition declaration is governed by Regulation (EU) No 1007/2011 on textile fibre names and related labelling and marking of fibre composition. Article 14 of that regulation requires textile products to be labelled or marked with an indication of their fibre composition, and Annex I sets out the prescribed list of generic fibre names. Here is the detail that catches brands out: the list does not contain “rayon” at all. The generic name for regenerated cellulose fibre obtained by the viscose process, entry 25, is viscose. If your tech pack says 20% rayon and your EU label says 20% viscose, those are not two ways of writing the same thing — one of them is wrong. Get the fibre name, the percentage and the order of the declaration identical across your tech pack, your hang tag and your invoice before you print labels, not after.
Our standing offer is simple: send us your specification sheet before you send us a purchase order, and we will tell you which lines we can certify, which lines we can test in a week, and which lines we cannot support for this construction. If you have never built a spec sheet from scratch, start with our guide to reading a fabric specification sheet like a pro. A supplier who answers that question in writing before the deposit is worth more than one who promises everything after it.
Decision
When YA8006 is the right pick, and when it is not
Every fabric has a buyer it suits and a buyer it will disappoint. Being precise about that is more useful than a list of adjectives, so here is ours.
YA8006 is the right choice when you are buying business suiting or office uniforms for a temperate or cool climate; when the garment will be pressed hard and worn daily rather than occasionally; when the budget has to survive industrial laundry cycles and repeated dry cleaning; when you want the drape of a viscose-blend cloth without paying for a wool blend; and when you need the same colour in multiple garments across several seasons, because we hold the base greige and can re-dye to the same shade year after year. If you are still weighing up where a polyester-rayon cloth fits your range, our piece on what polyester rayon fabric is used for lists the applications and advantages side by side.
YA8006 is the wrong choice when you need stretch — then specify our TRSP construction with spandex instead, because stretch is a fibre and construction decision that cannot be retrofitted; when the destination climate is hot and humid, where 360 g/m² is too heavy and you want the 240–280 g/m² version of the same blend; when you need the breathable drape of a tropical worsted at 200–230 g/m²; when luxury positioning is the priority and the hand feel of a wool or wool-polyester blend is what the customer is buying; when you need technical performance such as water repellency, stretch recovery or flame retardancy, which belongs in our functional fabric range rather than in a suiting TR; when your end use is hospital or industrial laundering, where ISO 105-C06 alone is out of scope and additional procedures are needed; or when you need a fully traceable recycled-content claim, which requires a certified recycled polyester component rather than a conventional TR.
One last comparison worth making, because buyers ask it constantly. YA8006 against a 100% polyester suiting of similar weight: TR drapes better, feels better under the hand and shows fewer crease lines, because the viscose component recovers the way polyester does not. Polyester wins on abrasion life and on wet rubbing, and it is cheaper. Against a 50/50 wool-polyester blend: TR is meaningfully lighter in price and often lighter in weight, wool wins on drape refinement and on the perception of luxury. What decides it is not the fibre, it is the wear protocol and the price the garment has to land at.
Commercial
Ordering YA8006: the eight steps from inquiry to shipment
Ordering YA8006 runs through a published eight-step ODM/OEM process, from your first inquiry to the moment the goods ship against the balance.
The eight steps are: you leave a message and we reply within 24 hours; we confirm price and delivery date; you approve a physical sample; we sign the contract and take the deposit; we start bulk production; we send a shipping sample for you to confirm against the approved sample; we pack and label to your instructions; and then we ship against the balance. There is no separate “sample stage” that turns into a second negotiation, and no production run that starts before the shipping sample has been agreed.
We publish these steps because the alternative is worse: a supplier who hides the process behind “we will figure it out later” is usually describing a production run they have not planned. With us, every step has a named owner and a confirmation point, so a buyer who has ordered once can predict the second order to the day.
YA8006 in garment form
The order path we run with every new customer is the same eight steps, and we publish it because the alternatives are worse: you leave a message and we reply within 24 hours; we confirm price and delivery date; you approve a physical sample; we sign the contract and take the deposit; we start bulk production; we send a shipping sample for you to confirm against the approved sample; we pack and label to your instructions; and then we ship against the balance. There is no separate “sample stage” that turns into a second negotiation, and no production run that starts before the shipping sample has been agreed.
For custom colour, send a Pantone reference or a physical swatch and we develop it into a lab dip, which you approve before bulk dyeing. We ask for the Pantone code in writing rather than relying on a screen, because a screen colour is not a colour and every mill that has accepted one has eventually paid for it.
Logistics run three ways — by sea, by air and by rail. Sea is the default for bulk yardage and always the cheapest per metre; air is for the samples, the top-ups and the urgent reorders; rail is the route we use for regular shipments into Russia and Central Asia, where it beats air on cost and still beats sea on transit time. Payment is by T/T, letter of credit, credit card or PayPal, and we extend account terms to customers who order more than once.
Summary
Five things to remember
- YA8006 is 80/20 polyester-rayon, serge twill, 360 g/m², 57/58 inch — a mid-to-heavy suiting and uniform cloth, not a lightweight tropical.
- Dry rubbing 4–5 and wet rubbing 2–3 under ISO 105-X12:2016. The dry result carries daily wear; the wet result is the number to specify if your laundering is industrial or your climate is hot.
- Laundering 4–5 for colour change with 4–5 cross-staining to all seven test fibres under ISO 105-C06:2010. That is the result that makes mixed-laundry uniform programmes workable.
- Pilling 4–5 after 7,000 Martindale cycles under ISO 12945-2:2020. It protects the appearance of the cloth, not the wear life of the garment — ask for ASTM D4966 if you need wear life.
- For the EU, the fibre name on your label is “viscose”, not “rayon”. Regulation (EU) No 1007/2011 prescribes generic fibre names, and regenerated cellulose fibre appears as viscose in Annex I. Sort the tech pack and the hang tag out before print.
- Ask for the specification sheet conversation before the purchase order. Send us your spec and we will tell you, in writing, which lines we certify, which we can test quickly, and which we cannot support for this construction.
FAQ
Questions buyers ask before ordering
01What does ISO 105-X12 actually measure?+
It measures the resistance of textile colour to rubbing off and staining other materials, with the specimen tested dry and then wet and the colour transfer read against a white backing cloth on a five-point scale. Grade 5 means no perceptible change, Grade 1 severe change. It is a surface colour test, not a durability or wear-life test.
02Is a wet rubbing grade of 2–3 acceptable for a school or office uniform?+
For most office, hospitality, airline and school uniform programmes, yes — because those garments are dominated by dry contact, and the dry grade of 4–5 is what governs appearance over a working life. Where it is not enough is in industrial or hospital laundering, in heavy perspiration, or where the garment is washed while still warm. Tell us your wash protocol at quotation stage and we will confirm the number for your specific colour before bulk dyeing.
03What does 7,000 Martindale cycles prove about pilling?+
That after 7,000 abrasion cycles under the modified Martindale method of ISO 12945-2:2020, the fabric still grades 4–5 for surface pilling — meaning the face will not fuzz up into visible pills under heavy wear. It does not measure how long the garment lasts, which is an abrasion resistance figure taken under ASTM D4966 instead.
04Does the washing result apply to hospital or industrial laundering?+
ISO 105-C06:2010 covers domestic and commercial laundering for normal household articles, and the standard itself notes that industrial and hospital articles may need additional procedures. If your end use is hospital or industrial laundry, tell us and we will run the additional procedures on your specific colour rather than relying on the household result.
05How does your order process work?+
We run a published eight-step ODM/OEM process: inquiry and 24-hour reply, confirm price and delivery, approve a physical sample, sign the contract and pay the deposit, bulk production, shipping sample confirmation, packing and labelling to your instructions, then shipment against the balance. Production runs do not start before the shipping sample is approved.
06Can we get our own colour, and how do we approve it?+
Yes. Send a Pantone code in writing or a physical swatch and we develop a lab dip for your approval before bulk dyeing. We ask for the Pantone reference in writing rather than relying on a screen colour, because a screen colour is not a colour.
Next step
Ask us to read your specification sheet
Send the lines you need certified and we will come back with which ones we test in-house, which ones we run at an external laboratory, and which ones we cannot support on a 360 g/m² polyester-rayon construction — before you place an order.
Figures verified 2026-11-19 · grades reproduced from our own examination report
Post time: Nov-19-2026



